home security about ordering-shipping currency converter
email here phone 07842 634090
SURFACE DRIVE HARDWARE
PMB
Model Boats
home security
about ordering-shipping
currency converter
email here
phone 07842
634090
SURFACE DRIVE HARDWARE
| SF2 | 3/16"
(4.85mm). Full set with 21.5 inch (540mm) flexishaft and stub shaft, drive
dog, brass tube, cnc machined aluminium strut with lead teflon
bearings. Suitable for mono's, cats and hydro's up to 11cc and brushless motors up to 4000 watts. Use with HF46 or HF49 rudder |
 |
 £27.90 |
| HF3 | 3/16"
(4.85mm). Same as HF2 flexishaft but 30" (730mm) long. Suitable for mono's, cats and hydro's up to 11cc and brushless motors up to 4000 watts. Use with HF46 or HF49 rudder |
|
£30.90 |
| HF35 | 3/16" (4.87mm). STINGER Surface Drive flexi-shaft assembly comprising 3/16" flexi-shaft with 3/16" stub shaft (21.5"overall length), drive-dog, brass tube, CNC machined aluminium stinger drive and all screws, washers, locknuts etc. Adjustable for angle. Engines .21 to .61 and larger electric motors in mono boats |  |
£39.90 |
| SF2 | 1/4"
(6.35mm). Surface
Drive flexi-shaft assembly comprising 1/4" flexi-shaft with 1/4"
stub shaft (18" - 457mm overall length), drive-dog, brass tube,
aluminium CNC strut
with lead teflon bearings, aluminium brackets and all screws, washers,
locknuts etc. Engines 11cc to
40cc. Suitable for mono's, cats and hydro's. USE WITH HF49 or HF49A rudders
|
 |
£32.90 |
| SF3 | 1/4"
((6.35mm). Same flex shaft as
SF2 but 25"- 635mm long. Suitable for mono's, cats and hyd's. USE WITH HF49, HF49Aor HF49B rudders |
 |
£34.90 |
| SF35 | 1/4"
(6.35mm). STINGER Surface
Drive flexi-shaft assembly comprising 1/4" flexi-shaft with 1/4"
stub shaft (25"overall length), drive-dog, brass tube, CNC machined
aluminium stinger drive and all screws, washers,
locknuts etc. Adjustable for angle. Engines 11cc to 40cc in mono
boats.
USE WITH HF49 or HF49A rudders on mono's and deep V's.
|
|
£42.90 |
| SF36 | 1/4"
(6.35mm). VS2 STINGER Full set. Surface
Drive flexi-shaft assembly comprising 1/4" flexi-shaft with 1/4"
stub shaft (25"overall length), drive-dog, brass tube with teflon, CNC machined
aluminium stinger drive and all screws, washers,
locknuts etc. Adjustable for angle and length of stinger.( 105mm to
125mm). Engines 11cc to 40cc in mono
boats.
USE WITH HF49 or HF49A rudders on mono's and deep V's.
|
 |
£48.90 |
| EM60 | Complete
Surface Drive Flexi-shaft assembly for Surface for dog drive 3/16 and 4mm
bore props (supplied with 4mm to 3/16 adapter tube) with 4mm flexishaft
for 540/700 size electric motors and similar brushless and .12/.15 nitro. Suitable for
Hydro's, Deep V’s and Catamarans.
Contains 4mm Flexi-shaft with 4mm stainless steel stub-shaft,
drive dog, PTFE teflon tube, strut with lead/teflon bushes, brackets and
all nuts, bolts needed. Flexi and stub is 350mm long but can be cut down
to length.
Longer lengths can be supplied suitable for mono's, cats, hydro's More electric hardware here FAST ELECTRICS . |
 |
£32.00 |
| EM60A | Same setup as EM60 but with 3.2mm flexi cable and stub shaft reduced to 1/8" (3.2mm) for smaller dog drive props.. flexicable is 350mm overall length. Couplings and hardware for FAST ELECTRICS | |
£32.00 |
| HF64 | Stinger drive. for 3/16 The most streamlined stinger drive available with sturdy adjustment. Very strong CNC machined aluminium drive unit with adjustment for shaft angle. Fitted with lead teflon bushes. | 
 |
£24.95 |
| HF69 | Stinger drive. 85mm long. Very strong CNC machined aluminium drive unit with adjustment for shaft angle and fitted with lead teflon bearings. For 1/4"flexis, welded or square drive.. |  |
£26.95 |
| HF69A | Stinger drive. 105mm long. Very strong CNC machined aluminium drive unit with adjustment for shaft angle and fitted with lead teflon bushes. For all 1/4"flexis, welded type or square drive type. |  |
£29.00 |
| HF69B | Stinger drive VS2 Adjustable 105mm to 125mm long. Very strong CNC machined aluminium drive unit with adjustment for shaft angle and fitted with lead teflon bushes. For all 1/4"flexis, welded type or square drive type. Easy adjustement from the back | 
 |
£32.00 |
| HF9 | Spare flexi-shaft. 3/16", 21.5" - 540mm long. |  |
£12.50 |
| HF10 | Spare flexi-shaft. 3/16", 30" - 760mm long. | |
£17.50 |
| HF11 | Spare flexi-shaft. 3/16", 24" - 610mm long. RIGHT HAND ROTATION | |
NO STOCK £16.50 |
| SF6 | Spare 1/4" flexi-shaft with 1/4" stub shaft, 18" - 457mm long. |  |
£13.50 |
| SF7 | Spare 1/4" flexi-shaft with 1/4" stub shaft, 25" - 635mm long. | |
£14.50 |
| SF7RH | Spare
RH 1/4" flexi-shaft with 1/4" stub shaft, 25" - 635mm long. for RIGHT HAND ROTATION |
|
£19.75 |
| SF8 | Spare 1/4"flexi-shaft 1/4" stub shaft., 30" - 750mm long. | |
£16.50 |
| SF9 | Spare 1/4"flexi-shaft 1/4" stub shaft., 36" - 900mm long. | |
£18.50 |
| SF6A | Spare flexi-shaft. 1/4" Flexi and 1/4"stub shaft turned down to 3/16, 18" - 457mm long. |  |
£19.30 |
| SF7A | Spare flexi-shaft. 1/4" Flexi and 1/4"stub shaft turned down to 3/16, 25" - 635mm long. |  |
£21.90 |
| SF8A | Spare flexi-shaft. 1/4" Flexi and 1/4"stub shaft turned down to 3/16. 30" - 680mm long. | |
£23.30 |
| SFSQ | SQUARE ended 1/4 flexishaft (square is 5mm across flats) Complete with 1/4" stubshaft, brass collet joiner and drive dog. Total length 620mm long |  |
£19.95 |
| SFSQ2 | SQUARE ended 1/4 flexishaft (square is 5mm across flats). 500mm long |  |
£9.95 |
| HSQ2 | SQUARE ended 3/16" flexishaft (square is 4mm across flats). 500mm long | |
£7.95 |
| SFSQRH | SQUARE
ended 1/4 flexishaft (square is 5mm across flats) RH 500mm
long
for RIGHT HAND ROTATION |
|
£11.95 |
| SFFERR | Brass ferrule for 1/4" round shaft and 1/4" round flexishaft | |
£4.50 |
| SFSQFERR | Stainless steel ferrule for 1/4" shaft and Square 1/4" flexishaft. 12.5mm od, 42mm long. 1/4 id at one end to fix onto the stubshaft and square 5mm across flats inside the tapered end. |  |
£6.95 |
| SFSS | 1/4 stubshaft 125mm long for use with ferrules and square drive. Complete with 2 thrust washers and a Zuber locknut |  |
£4.00 |
| SFWA | 10 x 1/4" id thrust washers 12mm od |  |
£2.00 |
| HF191 | Flexhex steel collet engine coupling. 1/4 unf (1/4-28) for 3/16" flexishaft. Suitable for all .21 engines and most .40 and .45 engines. |
|
£9.95 |
| HF192 | Flexhex steel collet engine coupling. 5/16 unf ( 5/16-24) for 3/16" flexishaft. Suitable for SC61/9ASP 61/91, OS 61 VRM, OS 81 VRM.1 |
|
£12.95 |
| HF192A | Flexhex steel collet engine coupling. 5/16 unf ( 5/16-24) for 1/4" flexishaft. Suitable for SC61/9ASP 61/91, OS 61 VRM, OS 81 VRM.1 |
|
£13.95 |
| HF193 | Flexhex steel collet engine coupling. M8 for 1/4" flexishaft. Suitable for CMB 90, Picco 90, CMB 67/80 |
|
£12.95 |
| HF194 | Flexhex steel collet engine coupling. Special for Zenoah Sikk for 1/4" flexishaft. This coupling slides onto the taper part of the shaft and has a separate locking collet for the shaft. |
|
£10.95 |
| HF194A | Flexhex steel collet only for HF194coupling. |
|
£4.95 |
| HF197 | Square drive coupling for Zenoah engines to fit 1/4 flexis with squared end. This coupling is the same as HF194 but has square collet inside |
|
£18.95 |
| HF201 | Collet coupling 1/4" with starter pulley for Zenoah Sikk RCMK etc. Allows you to use a belt start but retain the pullstart. |
|
£21.00 |
| HF199 | Square drive coupling for most .90 engines, CMB, Picco and Rossi, to fit 1/4 flexis with squared end. |
|
£10.95 |
| HF58 | Flexshaft grease. Special formulated waterproof teflon filled grease that sticks to the flexishaft. 30 grams. |
|
£2.95 |
| HF59 | NEW CNC machined aluminium T-Bar propshaft support. Fits between 5" rails and suitable for 1/4" flexishafts (11/32 or 5/16 tubes). brass lubrication point included for lubricating shaft. For supporting the tube in mono's . |
|
£15.95 |
| HF59A | NEW CNC machined aluminium T-Bar propshaft support with oil cup for lubricating the shaft. Fits between 5" rails and suitable for 1/4" flexishafts (11/32 or 5/16 tubes).. For supporting the tube in mono's . |
|
£21.95 |
| HF59B | NEW CNC machined aluminium COMPETITION T-Bar propshaft support with oil resovoir for lubricating the shaft. Fits between 5" rails and suitable for 1/4" flexishafts (11/32 or 5/16 tubes).. For supporting the tube in mono's . Each end is adjustable for length , oil resovoir inside. |
|
£22.95 |
| HF59C | BUTCH BLOCK Propshaft support for cats. CNC aluminium with shaft aligner. |
|
£21.95 |
| HF60 | LARGE stainless steel and CNC aluminium trim tabs for DeepV type boats. 48mm long, 76mm wide. 2 pieces. |
|
£16.95
|
| HF61 | MEDIUM stainless steel and CNC aluminium trim tabs for DeepV type boats. 45mm long, 57mm wide. 2 pieces. |
|
£14.95
|
| HF62 | Stainless steel and CNC aluminium trim tabs for DeepV type boats. 45mm
long, 57mm wide. 4 pieces.
NEW |
|
£17.95
|
| HF63 | CNC
aluminium large trim tabs with turnbuckle adjusters.
NEW |
|
£25.95
|
| HF45 | Wedge rudder for surface drive fast electrics or .12 to .18 engines. Built in waterscoop, highly polished CNC machined aluminium. Small rudder assembly with 95mm long rudder blade, leading edge 42mm from the transom. |
|
£14.95
|
| HF46 | CNC machined aluminium medium rudder assembly with 130mm (5") long rudder blade and builtb in waterpickup. for .21 to .45 size boats. |
|
£22.95 |
| HF49A | Standard rudder. CNC machined aluminium large rudder assembly with 160mm (6 1/2") long rudder blade and 100mm bracket (from transom to front of rudder blade). Twin waterpickups. (one pickup can be blocked off if not required) |
|
£31.95 |
| HF49B | TWIN water pickup (LONG BRACKET 150mm) CNC machined aluminium large rudder assembly with 160mm (6 1/2") long rudder blade. |
|
£33.95 |
| HF49C | RUDDER with SHORT BRACKET for cats and hydros. CNC machined aluminium large rudder assembly with 160mm (6 1/2") long rudder blade. TWIN PICKUP . |
|
£29.85 |
| HF55 | Twin rudder with adjustable 1/4 strut. Water pickup in each rudder. Anodised, CNC machined aluminium with rudder link bar. Large rudder assembly with 150mm (6") long rudder blade. |
|
£39.95 |
| HF55A | Strudder unit with rudder directly behind the strut. Single water pickup built into the strut. Please make sure its suitable for your boat. |
|
£39.95 |
| HF57 | Spare CNC machined aluminium rudder blade for HF49A, HF49B. Twin water pickup. |
|
£17.95 |
| HF57A | Spare CNC machined bearing block for all HF49A, HF49B, HF49C |
|
£8.95 |
| HF57B | Spare CNC machined aluminium 90 degree bracket for HF49A, HF49B, HF49C. |
. |
£5.95 |
| HF57A | 10 brass breakaway screws for rudders. These fit in the lower hole of the rudder pivot bracket and will break if the rudder hits something. Complete with locknuts. |
|
£3.50 |
| HF16A | STRUT CNC machined aluminium for 1/4 shafts. For mono's and cats. Includes CNC machined brackets, lead teflon bearings and all screws. |
|
|
| HF18 | Aluminium strut with lead teflon bearings and brackets. For 3/16" shafts. |
|
£12.50 |
| HF18A | Spare aluminium strut with lead teflon bearings. For 4mm shafts. |
|
£12.50 |
| HF18B | Long aluminium strut with skeg for cats. Fitted with lead teflon bushes , brackets and all screws etc. For 1/4 shafts |
|
£28.00 |
| HF20 | TURN FINS Large. Helps deep V in the turns. 2 large turn fins for gas boats CNC machined aluminium with CNC machined stainless brackets and screws. 90mm deep |  |
£12.50 |
| HF21 | TURN FINS Medium. Helps deep V in the turns. 2 medium turn fins CNC machined aluminium with CNC machined stainless brackets and screws. 62mm deep | |
£10.50 |
| HF22 | TURN FINS Small. Helps deep V in the turns. 2 small turn fins CNC machined aluminium with CNC machined stainless brackets and screws. 52mm deep | |
£8.95 |
| GA39 | Autobailer one way valve. Fitted to the back of the boat, the valve allows water out but stops water coming in. |  |
£4.80 |
| HF80 | 3/16" drive dog stainless steel |
|
£2.20 |
| HF80A | 3/16" drive dog for SMALL PROPS stainless steel. Dog end is tapered down to match the boss of smaller props from X437 to X445 |
|
£3.50 |
| HF81 | 1/4" drive dog stainless steel |
|
£2.50 |
| TEF14 | 2
pieces of teflon 1/4 liner 20" ( 2 X 500mm) long for 25" flexis
(40" total)
|
.
|
£6.95 |
| HF200 | Shaft saver 1/4. Clamps onto flexishaft between coupling and top end of tube to stop flexishaft being lost if coupling becomes loose. |
|
£3.00 |
| HF82 | Brass tube 1/4" o.d. for 15" 3/16 flexi. 12" long |
.
|
£3.00 |
| HF82A | Brass tube for 3/16" for 21.5 " flexi. 1/4" o.d. thin wall standard stuffing tube. 18.5" long |
.
|
£4.00 |
| HF83 | Brass tube for 1/4" flexis 18 ". 15" long 5/16 o.d. thin wall standard stuffing tube. |
.
|
£3.00 |
| HF83A | Brass tube for 25" 1/4" flexis. 21.5" long . 5/16 o.d. thin wall standard stuffing tube. |
.
|
£4.00 |
| HF83B | Brass tube for 30" 1/4" flexis. 26.5" long . 5/16 o.d. thin wall standard stuffing tube. |
.
|
£4.50 |
| HF83C | Brass tube for 36" 1/4" flexis. 32.5" long . 5/16 o.d. thin wall standard stuffing tube. |
.
|
£5.00 |
| HF85 | Rudder link for surface drive. 440 size (2.5mm)pushrod with heavy duty ball joint and heavy duty steel quicklink. | . | £4.95 |
| HF88 | 3/16" ( 4.87mm) lead teflon bushes. 1/4" od. ( 6.35mm) .4 pieces. |
|
£2.95 |
| HF89 | 1/4" (6.35mm ) lead teflon bushes. 5/16" od (8mm) 4 pieces |
. |
£2.95 |
| HF94 | 5mm id x 7mm lead teflon bushes .4 pieces |
. |
£2.95 |
| EM114 | 4mm id lead teflon bushes. 4 pieces. |
. |
£2.95 |
| EM115 | 1/8" id lead teflon bushes. 4 pieces |
. |
£2.95 |
| HF91 | 1/4" strut bushing |
|
£4.50 |
| HFT3 | 9/32 (7.1mm) "Brass tube with teflon liner for 25" 3/16 flexi. |
.
|
£8.00 |
| HFT5 | 11/32" (8.8mm) Brass tube with teflon liner for 25" 1/4 flexi. |
.
|
£8.00 |
| HFT7 | Teflon liner for 1/4 flexi. 2 pieces 20" (500mm) long. These are sent straight in a cardboard tube. |
.
|
£7.00 |
| RBX7 | RADIO
BOXES for all boats
See our other radio boxes here Model Boat Radio Boxes |
. |
|
| On the right is a typical mono setup with HF 49A twin pickup rudder, HF16A strut and HF20 turn fins. ( click to enlarge.) |
|
||
412
